How to Install Led Light Bar-4 Inch

FEATURED COLLECTION

Hot Sales

Dec 14, 2021 by Charlonette Baysan

Introduction

Over the past several years, LED lighting has emerged as a prominent technological innovation in the vehicle industry, particularly interior and exterior lighting. Many factors contribute to the popularity of these LED lights, including that they are energy efficient. Because they can be employed as a mixture of a spotlight and a floodlight, they are also highly versatile in their application.

4-inch LED light bars, commonly known as led pods or off-road light bars, are a more professional outdoor light source than basic car aids. When going off-road or camping, an extended range of illumination is needed, such as in the field of vehicle rescue, maintenance, or night camping. In this case, auxiliary lamps aren’t the ones to work perfectly, and professional lightbars come in handy. With IP68 rated construction, waterproof, dustproof, and shockproof performance, Novsights’ 4-inch lightbar can be used on various trucks, off-road vehicles, 4x4, military, mining, and heavy equipment, among other things.

Most customers who purchase Novsights' 4-inch LED lightbar to do so for their SUV or pickup truck. While some people like the wired version, others prefer the non-wired version because it can be installed much more quickly and easily without the need to drill holes in their car.

Get Started

Please note that a good understanding of the automotive electronics system and its procedures are required to install this product. If mounting this product on your will require drilling holes, you must ensure that no vehicle components or other vital parts will be damaged. Always check both sides of the mounting surface before you start drilling holes. Then, de-burr the holes and remove any metal shards or remnants before installing grommets into all wire passage holes.

A robust electrical connection to the chassis ground is required for this product to perform at optimum efficiency. According to the recommended procedure, the ground wire must be connected directly to the negative (-) battery post.

⚠️Don’ts

Do not mount this product or any wires in the expanded area of your airbag! It can damage, reduce the airbag’s effectiveness, and become a risk that could personally cause severe injury or death.

Do not attempt to activate or control this device in a dangerous driving condition.
Strobe light(s), high-intensity LEDs, or a combination of these lights are used in this product. If you stare directly into these lights, you may experience temporary blindness or damage to your eyes.
Cleaning the outer lens with soap and water is recommended; other chemicals may cause early lens cracking and discoloration, reducing its effectiveness and shortening its lifespan. Inspect this product regularly to ensure good operation and mounting. This product should not be cleaned with a pressure washer.

Get to know LED Light Bar For Jeep & Truck Violence Test

Mounting the 4-Inch LED Lightbar Using the L Bracket

1. Attach the side mounts to the lamps with bolts and tighten them down.
2. Drill M8 Bolt holes in the correct positions on the mounting plate where you want to attach the mounting plate to the base and where you want to fix the base to the mounting plate.

Mounting the 4-Inch LED Lightbar Using Pipe Mount Adapters

1. Attach the side mount to the lamps with bolts and secure it in place.
2. Attach the roll bar/pipe/tube clamps using the provided screws.
3: Thread the bolt through the clamp, the mount, roll bar, and then tighten the bolt.

Finally, Mounting the Lights!

1. Attach the side mount to the lamps with bolts and secure it in place.
2. Drill M8 Bolt holes in the correct positions where you want to attach the mounting plate to the base and where you want to fix the base to the mounting plate.
Or you can use this other method:
1. Attach the side mount to the lamps with bolts and secure it in place.
2. Attach the roll bar/pipe/tube clamps using the provided screws. Tighten the bolt after threading it through the clamp, mount, and roll bar.

Should You Buy LED Car Light Bars?

Many people, especially night drivers, rely on LED lights. LED lighting bars are ideal for people who live in the desert or travel on dirt roads. They assist you to see the road clearly and avoid being hit by other vehicles.

With LEDs becoming more popular, you can choose one that matches your car. You no longer need to be concerned about the lights' appearance.

Overall, LED light bars can help improve motorist safety. On the road, accidents can happen, and these devices can assist you in avoiding hitting another car. That alone should motivate you to choose the best light bar for your car.

Interested in buying one for your car? See what Novsight has to offer now!

4 Inch Led Light Bar with Wiring
4 Inch Led Pod Lights 120W
12 Inch Led Light Bar 240W

This product has no images.

LED Pod 4 Inch Bar Light Flood Spot Combo Kit for Trucks Off Road Jeep Wrangler Roof Bumper

38.99